What should you do prior to starting up the gas-powered inboard motor? Prior to starting up the inboard motor, check for vapour odours. If you have a gaz powered inboard motor, the blower must be operated for a period of at least four (4) minutes. This will enable any dangerous fumes to fully evaporate.

What should you do before starting inboard engine?

If you have an inboard gasoline engine, you need to turn on the blower for four full minutes before starting your boat. This very important step is to remove any fumes that could be lingering in the bilge. All portable fuel tanks must be filled off of the boat.

What to do before starting a boat motor that has been sitting?

What To Do If An Outboard Has Been Sitting For Awhile!

1. Remove the Spark Plugs & Oil The Cylinders, Replace Plugs if Needed.
2. Check the Condition of the Gear Lube.
3. Disconnect the Fuel Line From the Boat & Check the Condition of the Fuel.
4. Connect a Separate Fuel Tank with Brand New Fuel.

How long can a boat sit without running?

One of the most commonly-asked questions we get is, “Is it okay if my boat isn't running for a while in Fort Lauderdale, FL?” The answer is yes—but you have to do some maintenance beforehand. As long as it's well maintained before going into storage, a boat can sit for a few months, a few years or even a few decades.

What is the first thing to look for after starting outboard engine quizlet?

Check to see that fuel lines, connections, and fuel vents are in good condition. Turn off anything that might cause a spark—engines, fans, or electrical equipment. Shut off all fuel valves and extinguish all open flames, such as galley stoves and pilot lights.

Starting an Inboard Outboard Motor - The right way to start a boat!

17 related questions found

How do you start a flooded MerCruiser?

To restart when flooded, open the throttle all the way (with no choke), to admit as much air as possible, and crank the motor until the excess fuel is expelled.

Is it bad to start a boat without water?

Starting a boat without water is not recommended. Most outboard and inboard engines use impellers (rubber pumps) to run water to the boat's cooling system. Without water to cool off and lubricate, the impeller will heat up super fast and possibly damage.

What would cause a boat not to start?

Common Causes and Solutions for a Boat Engine That Won't Start. ... Boat engines need ignition, fuel, air, compression and exhaust to start up and run smoothly. If any of these elements are missing due to broken or damaged parts, your engine may not turn over and will have trouble starting.

How many minutes should a blower be operated before starting an engine?

DANGER: To prevent a possible explosion, operate the blower for at least four (4) minutes before starting the engine and always when at idle or slow running speed. Explosive gasoline and/or battery fumes may be present in the engine compartment.

How do you start a flooded engine?

To start the flooded boat engine, wide open the throttle (with no choke) and wait for a couple of seconds to send air inside the cylinder to compensate for the excessive gasoline present inside the flooded combustion cylinder and then try to start the boat engine.

Can any boat go in saltwater?

For the most part, freshwater boats can be used in saltwater. However, boat owners need to be aware of the increased potential for corrosion. ... Saltwater boats are designed to handle the more rigorous conditions that come with saltwater, so they should be fine to handle freshwater.

What should you do before starting an inboard gasoline engine quizlet?

Before starting an inboard gasoline engine, you should operate the blower for at least 4 minutes and: sniff the blower exhaust for traces of gasoline fumes.

What is the first thing to look for after starting your outboard engine?

Take the engine cowling off and check for fuel or water leaks. If you find leaks, consult your safe boating mechanic. Wipe everything down and spray with an anti-corrosive like WD 40 or Quick-lube. Be sure to lubricate all the moving parts, such as the shift, throttle cables, carburetor valves, etc.

What should you do before fueling your boat?

Shut off all fuel valves and extinguish all open flames, such as galley stoves and pilot lights. Close all windows, ports, doors, and other openings to prevent fumes from entering the boat. Remove portable fuel tanks from the boat and fill them on the dock. Make sure that your fire extinguisher is within reach.

How often should you run boat engine?

A few hours every week keeps the motor in better shape than using it two or three full days every month. The more often it gets used, the better it will run, just like any vehicle. If it's left sitting idle at the marina or in a garage for the majority of the time, parts tend to go bad faster.

How does inboard outboard work?

Inboard engines are mounted inside the hull's midsection or in front of the transom. The engine turns a drive shaft that runs through the bottom of the hull and is attached to a propeller at the other end. Many PWC have two-stroke inboard engines that burn oil as a lubricant along with the fuel.

How do you start a boat after winter?

How to De-winterize Your Boat

1. Take the Tarp Off. Before you do anything, you need to get the tarp or covering off your boat. ...
2. Check the Engine. ...
3. Refill the Cooling System. ...
4. Check Water Pumps and Thermostats. ...
5. Check Cables and Hoses. ...
6. Check Your Battery. ...
7. Clean the Distributor. ...
8. Check the Fuel System.

Where should water come out on an inboard motor?

Fresh seawater is normally drawn by a belt driven pump from a thru hull fitting in hull of boat on inboards, or by water pump in stern drive through the lower unit water passages on an inboard/outboard, and then exits the boat through the exhaust.

How long can you run a boat on muffs?

Don't run the engine unattended. Keep an eye on the muffs and make sure they don't slip off of the water intakes. Regardless of your task, it's unlikely that you'll need to run it more than 10 to 15 minutes.

Is it OK to run a boat motor out of water?

An outboard motor should never be operated without a source of water entering the inlet screens to supply the water pump. Without a source of water for lubrication, the water pump will be the first to be damaged, followed shortly thereafter by the engine from a lack of cooling.