If you're like a lot of pool owners, you might be wondering if it's safe to fill a pool with well water. The short answer is yes, you can – but there are some important things to consider before you proceed.

How long can you run a well to fill a pool?

Several factors go into whether or not your well has the capacity of handing filling a swimming pool. It's estimated at 540 gallons per hour, it will take about nine hours to fill a 5,000-gallon pool with a 1/2-inch hose. Most larger, in-ground pools are around 18,000-20,000 gallons.

How do I fill my pool with a well?

Steps to Follow

1. Fill the bucket with water from the well and add biocide. ...
2. Wait for five to ten minutes. ...
3. Connect the hose to the tap nearest to the well pump. ...
4. Place the open end of the hose inside your pool. ...
5. A small pool will take about 24-hour to fill while a large one will take 48-hour.

Can you use pond water to fill a pool?

Filling a pool from a pond is a fine idea. You may have a little more work getting the water ready for swimming, but people here have done it with success.

How much does it cost to deliver 10000 gallons of water?

If you don't trust your well, it will cost about $200 to fill a 10,000 gallon pool using a good water company that will deliver drinking water. Be careful, some water delivery people will back up to a local pond to fill up.

How to Drain Water From an In-Ground Pool With a Drain at the Bottom : Pool Maintenance

35 related questions found

How fast does well water replenish?

The water level in a well can regenerate at an average of 5 gallons per minute, but each well has a unique recovery rate. Whether it be the age of your water well, the location, or the geology, let's take a look at how long it takes for your water well to recover water.

Can you run out of well water?

Well water will run out if the groundwater level drops below the water intake depth. This can be caused by natural or man-made variations in groundwater height including reduced precipitation, slow groundwater recharge, well infill, high water usage, well drawdown or hydrofracking.

How many gallons does a well hold?

The typical 6-inch diameter well will hold approximately 1.5 gallons of water per foot of casing. The height of the water above the pump when it is not operating, multiplied by the gallons of water per foot of casing approximates the amount of available storage within the well casing.

Can you burn out a well pump?

Water Quality - A well pump can prematurely fail if you have poor water quality. Minerals can clog up the pump and cause it to burn out. ... If you continue to try to run the faucets, it will cause the well pump to 'call' for water and run. This can cause the pump to burn out.

How deep is average well?

In general, private home wells tend to range from 100 to 500 feet in depth. However, they can be much deeper than this in some cases. There are even some wells that go past the 1,000 foot mark. The average well depth in your area will depend on several factors.

What happens if you run your well dry?

When your well starts to run dry, you might notice reduced water pressure, sputtering faucets, and/or sediment in the water. The pump might run, but fail to draw water. ... Doing so could damage the well and contaminate your water supply.

How deep is a well for water?

Most household water wells range from 100 to 800 feet deep, but a few are over 1,000 feet deep. Well yields can be increased by fracturing the bedrock immediately around the drill hole and intercepted rock faults.

How long will a well last?

The average lifespan of a well is 30-50 years, although they can last longer or shorter depending on different circumstances. If the well you are buying is over 20 years old, you should at least factor in replacing the parts that commonly fail into your home buying budget.

How much water can my well produce?

A standard 6-inch diameter drilled well can store 1.5 gallons of water per foot. If you know the depth of the well, the level of the water and pump depth, you can figure out the water storage capacity.

Why are wells drying up nowadays?

A well is said to have gone dry when water levels drop below a pump intake. ... Amount and rate of pumping that occurs in the aquifer. Permeability and porosity of the underground rock. Amount of recharge occurring from precipitation or artificial recharge.

How much does it cost to shock a well?

How much does it cost to shock a well? If you hire a company to do it, it can cost anywhere around $100 depending on where you live. Doing it yourself will only cost as much as the chlorine, 10 gallon bucket and the safety supplies to do it.

Is 10 gallons a minute a good well?

Typical numbers for well recovery rates (if measured honestly over a 24-hour period) run from a fraction of a gallon per minute (a terribly poor well recovery or flow rate) to 3 gallons a minute of water flow (not great but usable) to 5 gallons per minute (just fine for residential use) to more than 10 gpm (a great ...

How much rain does it take to refill a well?

The rainfall that seeps into the ground on your property moves through the soil at a rate of only 10 feet per year. Since aquifers (where your well gets its water supply) are hundreds of feet below ground, it might take more than a decade for that rain to reach an aquifer or water-bearing strata!

Does a well need maintenance?

Regular maintenance of your well is required to ensure the continued safety of your water and to monitor for the presence of any contaminants. ... All hazardous materials, such as paint, fertilizer, pesticides, and motor oil, should be kept far away from your well.

How does well water replenish?

Groundwater supplies are replenished, or recharged, by rain and snow melt that seeps down into the cracks and crevices beneath the land's surface. ... A well is a pipe in the ground that fills with groundwater. This water can be brought to the surface by a pump.

Can I buy water to fill my pool?

Believe it or not, you can get pool water delivered, almost as easily as ordering from Amazon. There are companies that will bring a tank of water to your house, and use high-capacity hoses to fill your pool quickly.

How long does it take to fill a pool with a garden hose?

With a standard size 1/2 inch garden hose, it takes about 9 hours to fill a 5000-gallon pool. To figure the time needed yourself, multiple the number of gallons your pool holds by . 0018. The volume of water a standard hose can deliver per minute is approximately 9 gallons or 540 gallons in an hour.

How far from the bottom of a well should the pump be?

Pumps should never be set directly at the bottom of a well. It is usually best to place the pump 10 to 20 feet up from the bottom of the well.